A1 Foundation Crack Repair Blog

Too many people are dealing with wet basements. Now that the hurricane is over you can address your wet basement problems and be prepared (and relaxed) for the next time. You need to not only clean up the water, but you need to prevent basement floods from happening again. Because, as many people found out, sump pumps are great, but if there is no power, there isn't a whole lot you can do.

Keep in mind that you have about 48 hours to get your basement dry before mold starts to grow. Water extraction is the key. It is important to get dehumidification equipment into your basement. You need the air to be dried out and dehumidified. Often sheet rock or plaster has to be removed and you need to get air behind the walls in order to get it dry. 

After you have your basement dried out, you need to take steps to ensure that you don’t get water again. It is a fact, if you get water in your basement once, you will get it again.   The first step is to figure out where it came from in order to address the best way of eliminating it in the future.

If you got water in your basement from the hurricane, contact A1 Foundation Crack Repair so we can help prevent you from EVER taking in water again.

Comments (0) | Trackbacks (0) | Permalink |

There are plenty of homes out there with leaky basements. Many homeowners just assume their basement will be dark and damp. Maybe the concrete floor has a crack, or the foundation leaks a bit, or perhaps there is a leak where the pipes go through the basement walls. Through a towel on that, clean that right up and you’re all set right? Wrong.

Even if you don’t have a finished basement, even if the water doesn’t bother anything at all, you should take basement leaks seriously. Here's why:

Insects - There are many insects that seek out dark and damp areas including termites, cockroaches and spiders. We aren’t just talking about not liking bugs here. Termites and wood boring beetles, can damage your home. But insects can also cause health problems and they very challenging to get rid of without taking serious steps that involve harsh chemicals.

Health Problems - Mold and mildew dark and damp places, and damp basements are the perfect habitat. Mold can have serious effects on your family’s health, especially if there are asthma or allergies involved. Mold can increase the asthma attacks and itchy, watery eyes.

Integrity of your Foundation - A small wall or floor crack may seem harmless. But that crack may be hiding something bigger that you just can’t see.  If your doors aren’t shutting right floors are starting to warp this could be a result of the leak in your basement.

Resale value – Adding a basement to the list of amenities of your home when you  go to sell is a huge advantage. However, listing a home that has water damage in the basement is a big red flag. With all the homes on the market, and all the choices buyers have today, your home needs to be as enticing as ever to attract buyers.

Comments (1) | Trackbacks (0) | Permalink |

It has been very hot around here with no rain in sight really, so wet basements probably have not been on your mind. But with this humidity you could still have trouble in your basement.

Hot and humid weather just increases the humidity and moisture in your basement. High humidity can lead to mold and mildew growth. Depending on the severity, conditions can lead to rot, structural damage, premature paint problems, and health problems.

High indoor humidity caused by normal activities of everyday living, such as showering, cooking, and drying clothes, can also be a source of your problem. A damp basement is commonly caused by moisture migrating through a concrete foundation. There may not be a sign of any leak or standing water, but the moisture evaporates, increasing indoor humidity. Another common cause is condensation on the cold concrete walls and floors during humid months.

There are only two possible ways to eliminate condensation: heat the air or pull the moisture out of it. Obviously heating your basement to match the outside temperature is counterproductive, so the only real option is to dehumidify.

Comments (0) | Trackbacks (0) | Permalink |

No one enjoys a flooded basement. It is one of the worst problems for homeowners to face. Regardless of if your house gets water regularly or if it happens once a year, there is never a good time for water in the basement. To prevent basement flooding you need to understand why it is happening in order to properly fix the problem and to prevent it from reoccurring.

Sometimes basement flooding is caused by a water main break or really severe, and uncommon weather. In these instances, maybe you will never again have water in your home. However, most of the time basement water is recurring and those who have it, have it often. There is a way to fix this.

If your home is located on a sloped piece of land then there is a very good chance that water on the property will drain towards you. Obviously this could result in water damage to your home.

Many times water damage will be a result of problems with your plumbing, or pipe penetration leaks in the foundation. Again, these are problems that can be avoided in the future. You should check the plumbing to ensure that there are no signs of leaks and be sure that the pipe fittings are tight.

Concrete floor cracks and foundation cracks result over time. It is very important to have these repaired correctly and quickly. Ignoring cracks could compromise the integrity of the structure.

Bulkhead leaks are another way that water enters the home. The seal between your home and your bulkhead moves during the winter and needs to be fixed.

Regardless of how the water enters your home, it can be avoided. It is important to have these issues taken care of professionally for the safety and security of your home as well as the ability to sell your home in the future.

Comments (0) | Trackbacks (0) | Permalink |

It is summer and the basement is moist. You may not see any water, but if you can smell it and feel it, it is there. You may have a basement water proofing system in place, or perhaps you don’t have water seeping in your foundation from pipes or floor cracks. That’s the good news. The bad is that, this doesn’t necessarily mean that your basement is dry.

Often water enters a basement through capillary action, which wicks moisture through walls and floors. The floor and walls may not leak, but it feels damp to the touch because it wicks the water in to the surface. Water vapor also slowly seeps in through the concrete and raises the humidity. Basements act as chimneys pulling the outside air in the house and letting it out on the upper floors.

Humidity increases and condensation results as the hot outside air meets the cool basement.  Even without condensation basements tend to have high humidity levels and mold grows rapidly, generating that musty basement odor. Dust mites love that high humidity too.

There are only two possible ways to eliminate condensation: heat the air or pull the moisture out of it. Obviously heating your basement to match the outside temperature is counterproductive, so the only real option is to dehumidify.

Comments (0) | Trackbacks (0) | Permalink |

The purpose of a dehumidifier is to lower the humidity of the air in your home.  Humidity is a measure of the moisture suspended in the air at any given time.  Moisture levels are higher during different seasons.  In Massachusetts, humidity levels are much higher in the summer than in the winter. 

Home dehumidifiers are mostly used to dry air in the basement or crawlspace.  These areas are prone to high humidity levels because they are below ground.  It is not uncommon for the saturated ground outside of foundation walls to cause seeping or leakage through the walls.

The condensation is what allows a home dehumidifier to work. The dehumidifier typically consists of a metal or plastic cabinet that contains a fan, a compressor, metal coils and a collection pan.  There is also a humidistat that allows you to set the level of humidity you desire within a room.

The fan draws air into the unit, and it passes over the coils.  The coils are often set up as a two-stage process.  In the first stage, the coils are very cold.  As the air passes over the cold coils it condenses and collects there.  From here the water drips into the collection pan.  As the air continues on through the unit, it hits the second stage of coils which uses the heat generated by the compressor to re-heat the air and deliver it back in to the room.  

In the meantime, the collection pan fills with water.  The shut off is triggered when the water reaches a certain level.  Sometimes, rather than a collection pan, home dehumidifiers have a fitting that can attach to a hose so that the water can run out of the unit to a drain of your choice.

Understanding the basics of how a home dehumidifier works is important so that you can determine which type of unit to buy for your home.  A high quality, low maintenance unit is the best choice for most homes.  Compare home dehumidifiers carefully before investing in them, this is an important piece of equipment.

Comments (0) | Trackbacks (0) | Permalink |

In order to know how to waterproof a basement, you need to know how water enters the basement. There are many different ways water can enter the basement:  floor / wall joint, floor or wall crack, or through the bulkhead, to name a few.

Here we are going to talk about how water enters through the floor/wall joint.

The floor/wall joint is the most common entry source of water entering the basement. This is where the foundation wall meets the floor. The water comes in from the outside over the footing under the foundation wall and through where the foundation wall and floor converge. This is seen mostly when it rains. Water may seep in from other locations, but the most heavy water intrusion will be from the floor/wall joint.

When one concrete structure is poured (the floor) and another concrete structure is poured on it or next to it (the wall), a seam is created between the two concrete structures. Each concrete structure (the footing, the wall and the floor) is poured separately. There is a seam between each of these three structures. This allows the potential for water to come into the basement. There are four potential points of entry now: over the foundation footing, between the foundation walls, underneath the foundation and up through the seams between the foundation footing and the floor. This floor/wall joint seepage is very common and is a predominant reason for basement flooding.

Comments (0) | Trackbacks (0) | Permalink |

If you find that there is mold growing in your home from a wet or damp basement, you need to act fast in order to remove it. However, if you have a mold problem that covers more than a 10-foot by 10-foot area, consider calling a professional.

When dealing with mold removal, be careful, once mold is disturbed it will release mold spores that can cause additional growth, or those spores can lead to health problems.

The first phase of work will be to completely remove drywall and carpet and all other “non permanent” affected items.  Also remove any furnishings that are carrying mold.  It is rare that these items can be saved once they have mold.

Once that is completed, it is time to clean the mold.  Use a cleaning product that is designed specifically for mold removal.  This will ensure that the spores have been killed, and the entire mold organism has been removed.  You must be very thorough, especially in wall and ceiling cavities. 

Remember that mold spores are often invisible.  So, even though the visible mold has been removed from surfaces, the spores could remain in the air for quite some time. It is very important to isolate the area where you have mold from the rest of the house because mold spores are designed to travel in the air until they can find a place to settle which is good for growth.  Mold spores need warmth, moisture, and a food source.  The food source can include wood, drywall, paper, fabrics and other typical household items. 

The next step is to eliminate the moisture and the food source.  The mold cleaning detergent needs to eliminate the food source from the washed surfaces but you also need to lower the humidity levels in the area.  The temperature in the space should be higher than normal because this will promote faster drying.  Be sure to close any windows or doors to the outside as well, so that humidity from the outdoors cannot come in.

The basement or other affected area should have good airflow for several days, so use fans; but most importantly, be sure to have a dehumidifier in this space.  It should be a reliable, powerful unit that will remove moisture from the air into either into a reservoir or a hose running to a drain or sump pump.  With a moisture meter you can regularly check surfaces and materials for moisture content.  Once you are able to get walls and floors to 12% moisture content or less, mold growth can no longer be sustained.

Comments (0) | Trackbacks (0) | Permalink |

If basement water problems can be solved, you can gain some valuable storage or living space.  There are two ways to go about approaching water issues. The first is to address the leak from the outside of the foundation and the second is to deal with the problem from the inside. From both directions, there are waterproofing techniques designed to seal water out, and others that are designed to divert water from the foundation.

Waterproofing techniques and supplies that are generally used by do-it-yourselfers to seal water out of the basement include spray on sealants, membranes, and injection expanding epoxy waterproofing supplies designed to fill and seal cracks in solid concrete foundation walls. These are some of the least reliable methods of keeping water out because over time, they all succumb deteriorate.

There are also waterproofing supplies and techniques for diverting water on the exterior of the home. Dirt fill can be used along foundation to make the ground slope away from the house. This allows for water to runoff away from the home.

Regardless of the method you choose, exterior repair work is messy and expensive. The installation of anything on the exterior of the foundation will require excavation to expose the wall.

On the interior, the A-1 method of sealing out water from concrete floor cracks is with the gravity fed system. A polymer is used to create a bond between the concrete cracks and fills the entire void through to the bottom. The A-1 preferred method for foundation wall pipe penetration leaks is to inject the gap around the pipe with high-viscosity polyurethane. This polymer can be used on both wet and dry materials, and it can work its way into small hairline cracks to make a more powerful bond.

A-1 Foundation Crack Repair, Inc. was founded after more and more house builders requested the A-1 Method to solve problems that otherwise would have been cost prohibitive or simply too invasive. In fact, the A-1 Method not only repairs your existing cracks, but also helps prevent future ones!

Comments (0) | Trackbacks (0) | Permalink |

Mold problems might occur with home basement dampness or flooding. Mold is a living organism that thrives in wet or damp environments. Usually, the food source for mold is cellulose such as the paper on drywall, wood products or paint on concrete. It can even appear on the surface of metal in the right conditions.
 
Therefore a home and its contents are a food source for mold. Many people believe that molds can be cleaned with household bleach. When you clean mold with bleach you will see the mold disappear. But the underlying root system of them mold is unaffected by the bleach, and the molds will reappear within a few days.

You can't clean mold; it must be removed from your home. In the case of mold-infested drywall, paneling and acoustical ceiling tiles, the damaged areas should be cut out and discarded. You do not often see mold on older homes with plastered walls, but it will appear on the paint on the plaster. When this happens, the paint should be scraped off to remove the root system before repainting.

Mold usually does not appear on fabrics, but they can carry mold that can be transferred to cellulose and wood products in your house. So, wet or damp carpeting should be removed to allow the wood-floor surface to dry. Vinyl floor coverings also must be removed if you notice dark spots forming under the finished surface of the vinyl.

If you have a large mold problem in your home, it should be professionally mitigated and the humidity in your home should be controlled with a dehumidifier. Cracks in the basement concrete floor and/or foundation that allow in water need to be repaired. Continuous water damage or moisture in your home exacerbates the mold problem and may lead to issues with the structural integrity of your home or foundation.  The most important control for mold in any home is humidity control. Keep the area dry, because without moisture, though molds may be present, it cannot thrive.

Comments (0) | Trackbacks (0) | Permalink |